FENNER TAPER LOCK PDF

Fenner Taper Lock® bushes are machined in cast iron and steel and are available in a full range of both metric and Imperial bores and keyways. They ha. You can find the largest assortment Taper Lock bushes metric bore at ERIKS. Choose from FENNER Taper Lock® bush metric bore size · Taper Lock® . Fenner Taper-Lock Weld-on Hubs are easy to install and are entirely suitable for use. where severe operating conditions are met. Tightening the screws.

Author: Mezishura Mezir
Country: Burkina Faso
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 11 April 2005
Pages: 13
PDF File Size: 5.67 Mb
ePub File Size: 4.40 Mb
ISBN: 506-8-65721-797-7
Downloads: 25943
Price: Free* [*Free Regsitration Required]
Uploader: Mikree

It is important to note that the holes need to be matched, not the threads. Taper bushes are available in both imperial and metric shaft sizes, ranging from 0. Yaper other manufacturers generally manufacture Taper Lock bushes with an odd number of holes. Screws should be tightened alternately and evenly until all screws are pulled up and the bushing is square into the hub. Place the bushing into the hub and match half holes to make complete holes.

Fenner Taper Lock Bushing Series Mm Bore | eBay

We have sent you an email enclosing confirmation link, on your ID. In sizes where washers are found under the screw head, be sure to use these washers. The Taper Lock bush is pre-bored and keyed to match the required shaft and keyway diameters.

A torque wrench is used to tighten the screws alternatively and evenly until they are all to the recommended torque setting. Both Martin and Fenner Taper Lock bushes are manufactured in their full range of bushes with an even number of holes, i.

Note that special bores and keyway sizes can be supplied by CBC on request. Then place the screws loosely into the holes that are threaded on the hub-side, as shown in Figure 1 below. Please enter your e-mail address and we will send you a confirmation mail to reset your password. How to Fit a Taper Lock Bush.

  CHIROTECHNOLOGY INDUSTRIAL SYNTHESIS OF OPTICALLY ACTIVE COMPOUNDS PDF

Fenner Taper Lock Bushing 5050 Series 120 Mm Bore

The Taper lock bush is manufactured lick precision cast iron, and is machined to a high quality finish. This will prevent cracking of the bush. Oil threads, the point of the set screws or threads, and under the head of the cap screws. This information is available from the installation sheet that accompanies any new Taper Lock bush. Continue Browsing Continue to login.

Insert screws into the holes that are threaded on the bushing side, as shown in Figure 2.

Each hole will be threaded on one side only. It is computer-etched for ease of size identification and it may be manufactured in fenmer or stainless steel upon request.

Your password has been reset successfully. Ensure there is an air gap between the top of the key and the bushing keyway slot.

Taper Lock Bushes

Ensure that there is no oil or lubricant between the taper on the outside of the bushing and the taper bore of the hub, to which the bushing is being installed. Clean the shaft, the bore, the outside of the bushing, and the bore of the hub in which the bush is to be installed into, ensuring the bush is removed from the hub, should it already be installed.

See example chart below figure 3or ask for this information at any CBC office. The Taper Lock bush needs to be thoroughly cleaned, removing all traces of oil, grease, dirt, and metal filings. The presence of lubricant on the tapered surfaces is not desirable, as the taper bushing relies on friction fdnner operate effectively, and lubricants reduce friction.

  BUBA JOSE QUINTERO PDF

Expected price per piece. Pack of 1 pieces.

Fenner Taper Lock Bush Installation Video

When installing or removing a Taper Lock bush, it is imperative that no lubrication be used between the taper. Ensure that the Taper Lock bush is free in the hub, then slip the assembly onto the shaft and locate in the desired position.

The Martin and Fenner Taper Lock bushes featuring the fourth hole make them a preferred option in higher speed applications where balancing of the drive is critical. Check the bushing to ensure all surfaces are free from nicks and burrs, and ensure the bushing has no signs of cracking or fatigue. All quality manufacturers lkck also supply an installation instruction sheet with the bush.

Tighten the screws alternately until the bushing is loosened in the hub. The screws are then tightened further. To view the demonstration video showing installation and removal of a Taper Lock bush, please Click Below; When installing or removing txper Taper Lock loxk, it is imperative that no lubrication be used between the taper.

Email this to a friend or colleague! We will get back to you shortly! Sign In with your Industrybuying Account. Thanks for contacting industrybuying! Enter Details for faster checkout. I saw this product on industrybuying.

Installation of a Taper Lock Bush. Warranty As per Fenner’s policy. Thank You for your valuable feedback. Please enter correct email.

Please share your feedback and help us improve! Using a hammer and block, or sleeve, against the large end of the Taper Lock bush will help to avoid damage to the bushing.

Share